4WD JACK |AIR COMPRESSORS | BOW & D SHACKLES | DEEP DISH TRAY MATS | EQUALISER STRAPS | EXHAUST JACK | HAND WINCHES | HITCH RECEIVER | Pocket chain saw | REAR WHEEL BAG | RECOVERY DAMPER | RECOVERY GLOVES | RECOVERY KITS | RECOVERY STRAP DRYING BAG | SHOVELS | SNATCH BLOCK | SNATCH STRAPS | TREE TRUNK PROTECTORS | TOW HOOKS | TYRE REPAIR | TYRE GAUGES | WINCH STRAPS

Bow & D Shackles

Shackles are an essential recovery item and you can never have too many of them. They are most commonly used to attach recovery straps, tree trunk protectors, winch extension straps & snatch blocks. The larger 4.7 tonne shackles are best suited to electric winch recovery situations.

The most commonly used shackle is the "Bow" because its shape allows for bulky items to be easily attached. Shackles should only be used on vehicles fitted with recovery rated points featuring closed eyelets.

Alert TIP: To avoid seizing the screw pin, its always a good idea to back off about 1/2 to 1 turn after fully hand tightening. Shackle pins can seize due to the force exerted during recovery operations.
Tip Before use: Inspect shackles before and after use for any damage. If pins are hard to turn or the shackle has been overstressed, it should be immediately replaced.
Caution Caution: Shackles can become a lethal missile if something should break or fail during a recovery. Ensure that all spectators are well clear and all recovery lines have a dampening blanket on them (Refer page 41). Never load a shackle across its width because the load will be imposed on the threads. The force must be at right angles to the pin.
16 x 19mm - 3.25T Bow Shackles

16 X 19MM - 3.5T BOW SHACKLES

High visibility bow shackles. W.L.L compliant with AS/NZS 2741.2002 load requirements.

Part No: MM511
ERRP: $13.99
Max capacity 3500kg

Complies with Australian Standards

19 x 22mm - 4.7T Bow Shackles

19 X 22MM - 5T BOW SHACKLES

High visibility bow shackles. W.L.L compliant with AS/NZS 2741.2002 load requirements.

Part No: MM512
ERRP: $18.99
Max capacity 5000kg

Complies with Australian Standards

16 x 19mm - 3.25T D Shackles

16 X 19MM - 3.25T D SHACKLES

High visibility D shackles. W.L.L compliant with AS/NZS 2741.2002 load requirements.

Part No: MM513
ERRP: $13.99
Max capacity 3250kg

Complies with Australian Standards

19 x 22mm - 4.7T D Shackles

19 X 22MM - 4.7T D SHACKLES

High visibility D shackles. W.L.L compliant with AS/NZS 2741.2002 load requirements.

Part No: MM514
ERRP: $18.99
Max capacity 4700kg

Complies with Australian Standards

Tow Hooks

Back to top

Most 4WD vehicles are equipped with rated recovery points which are usually detailed in the owners manual.

Each tow hook is supplied with hardware to complete installation however some may require additional fittings. For added safety the tow hook has a spring steel retaining clip, to prevent straps from falling off during a recovery.

CautionCaution: A tow ball or vehicle tie down point is not designed as a recovery point. These points DO NOT have sufficient load ratings to handle the loads exerted during a recovery. Failure to attach recovery straps to a correctly rated recovery point may result in a failure and the strap, tow ball or other item used in the recovery may become a missile and could result in serious injury or death.
Black Tow Hooks

Black TOW HOOKS

Made from 1045C hardened carbon steel. Working load limit (WLL) 4500kg/10,000lb. Safety latch and hardware included.

Part No: MMHKB
ERRP*: $22.99
Max capacity 4500kg

Chrome Tow Hooks

Chrome TOW HOOKS

Made from 1045C hardened carbon steel. Working load limit (WLL) 4500kg/10,000lb. Safety latch and hardware included.

Part No: MMHKC
ERRP*: $24.99
Max capacity 4500kg

Chrome Tow Hooks

YELLOW TOW HOOKS

Made from 1045C hardened carbon steel. Working load limit (WLL) 4500kg/10,000lb. Safety latch and hardware included.

Part No: MMHKY
ERRP*: $24.99
Max capacity 4500kg

Snatch block

   

Back to top

Snatch blocks reduce the load placed on a winch when performing a recovery or to avoid damage when changing the direction of the cable.
The snatch block has two outer steel casings which swivel apart and allow the winch cable to be placed over the pulley wheel. Attach snatch blocks to appropriately rated recovery accessories such as tree trunk protectors or extension straps. Connection should be made using rated Bow or D shackles through the eyelets on the two outer casings of the snatch block.

Caution
Snatch blocks increase the pulling capacity by 1.5 times for each snatch block used. When using a snatch block your line pull speed is reduced.
Snatch Block

8T SNATCH BLOCK

8000kg capacity, heavy duty neoprene storage bag for protection when not in use.

Part No: MMSB8T
ERRP*: $69.00

Snatch straps

   

Back to top

All Mean Mother snatch straps are made here in Australia and tested to meet the highest quality and strength standards. They are manufactured from 100% treated nylon webbing with reinforced eyelets to prolong operational life. Similar to a rubber band, a snatch strap being stretched between two vehicles generates a kinetic energy pulling force as the strap returns to its original length. The combination of the recovery vehicle pull and the pulling force from the strap creates a ‘snatching’ effect that can heave a stranded vehicle free from being bogged or unable to move under its own power.

Caution
When used in accordance with the “Guidelines for safe use of vehicle Recovery Straps”, vehicles may be recovered with minimal risk of injury to people or damage to vehicle equipment.
CautionFACT..
All Mean Mother snatch straps are made from quality nylon webbing with 20% elongation. All our snatch straps meet Australian standards.
Snatch strap

aussie made

9M X 60MM - 8T

Australian made, high tenacity nylon webbing. Kooper reinforced eyes, thermo fixed and treated for longer wear. High elongation of 20%.

Part No: MMSS8T
ERRP*: $79.90
Minimum breaking strength 8000kg

Snatch strap

aussie made

9M X 75MM - 11T

Australian made, high tenacity nylon webbing. Kooper reinforced eyes, thermo fixed and treated for longer wear. High elongation of 20%.

Part No: MMSS11T
ERRP*: $99.90
Minimum breaking strength 11,000kg

recovery strap drying bag

   

Back to top

Designed to allow the airing of a recovery strap after use in wet conditions. The mesh construction provides the necessary ventilation to ensure maximum air flow and drainage. For the quick drying of straps, the bag can be left in direct sunlight but only for short periods of time.

Caution
Continued use in direct UV light will fade the bag and reduce the strength of both the bag and recovery strap.
Snatch strap

RECOVERY STRAP DRYING BAG

The large (44.5cm x 39cm) PVC coated polyester bag will accommodate most recovery straps. The sewn-in loop strap allows it to hang over a bull bar or ute racks.

Part No: MMRDB
ERRP*: $19.95

REAR WHEEL BAG

 

Back to top

From dirty recovery gear, to rubbush to wet beach towels, the Mean Mother Rear Wheel Bag will save your vehicles interior while giving you that extra space. Made from heavy duty materials this bag will stand up to all weather conditions. Increase your storage options and attach a Rear Wheel Bag ready for your next adventure!

jack carry bag

Rear wheel bag

This rear wheel bag is made from heavy duty material with adjustable straps, and features reflective strips for increased visibility.  The special anti-theft tag allows use of a padlock to secure the bag to the rim of your spare wheel, while the zipper over-flaps help to protect against dust, sand, and rain.

 

Part No: MMSBG
ERRP*: $119.00

Storage bag Mounting harness

The storage bag mounting harness is designed to allow secure attachment of your Mean Mother Rear Wheel Bag to the rear wheel carrier on most 4WD vehicles.

The durable straps are fully adjustable for quick and easy fitment.

 

Part No: MMSBH01
ERRP*: $34.95

storage bag Mounting strap

This fully adjustable mounting strap kit allows for the secure fitment of a Mean Mother storage bag to the tailgate on most style-side utility vehicles.

 

 

 

Part No: MMSBH02
ERRP*: $14.95

recovery kits

   

Back to top

Caution
When using a snatch strap carefully follow the safety guidelines set out in the instruction sheet included with each kit.

Having a fully stocked and properly maintained recovery kit is an essential accessory for any 4WD enthusiast. It is very important to have quick and easy accessibility to all your recovery equipment. Each Mean Mother recovery kit has been carefully tailored to include the correct equipment for most recovery situations.

5 PCE KIT:

Ideally suited to the 4WD adventurist who does not have a winch fitted to their vehicle or a hand winch on board. The 5 piece kit requires the assistance of another vehicle to complete a snatching recovery.

8 PCE KIT:

Best suited to the 4WD enthusiast who has a winch installed on the vehicle or a hand winch on board. Designed to maximise winch capabilities, performance and versatility. The kit offers users the ability to self recover or perform a snatching recovery.
Kit 5 piece

aussie made

RECOVERY KIT - 5PCE

Kit includes:
1x 8000kg Australian made snatch strap
2 x 3.5 tonne bow shackles
1 x Pair of gloves
1 x Heavy duty storage bag

Part No: MMKIT01
ERRP*: $139.90







Kit 8 piece

aussie made

RECOVERY KIT - 8PCE

Kit includes:
1x 8000kg Australian made snatch strap
1 x 4500kg winch ext strap (10m x 50mm)
1 x 6500kg tree trunk protector (3m x 75mm)
1 x 8000kg snatch block
2 x 5 tonne bow shackles
1 x Pair of gloves
1 x Heavy duty storage bag

Part No:MMKIT02
ERRP*: $269.90

Kit 5 piece

aussie made

RECOVERY KIT - 5PCE

Kit includes:
1x 11000kg Australian made snatch strap
2 x 5 tonne bow shackles
1 x Pair of gloves
1 x Heavy duty storage bag

Part No: MMKIT05
ERRP*: $169.90







Kit 8 piece

aussie made

RECOVERY KIT - 8PCE

Kit includes:
1x 11000kg Australian made snatch strap
1 x 4500kg winch ext strap (10m x 50mm)
1 x 6500kg tree trunk protector (3m x 75mm)
1 x 8000kg snatch block
2 x 5 tonne bow shackles
1 x Pair of gloves
1 x Heavy duty storage bag

Part No:MMKIT08
ERRP*: $289.90

Kit 5 piece

aussie made

RECOVERY KIT - 8PCE

Kit includes:
1x 8000kg Australian made snatch strap
1 x 8000kg Winch ext strap 10m x 50mm
1x 12000kg tree trunk protector (3mm x 75mm)
1 x 8000kg snatch block
2 x 5 tonne bow shackles
1 x Pair of gloves
1 x Heavy duty storage bag

Part No: MMKIT09
ERRP*: $329.90

Kit 8 piece

aussie made

RECOVERY KIT - 8PCE

Kit includes:
1x 11000kg Australian made snatch strap
1 x 8000kg winch ext strap (3m x 75mm)
1 x 12000kg tree trunk protector (3m x 75mm)
1 x 8000kg snatch block
2 x 5 tonne bow shackles
1 x Pair of gloves
1 x Heavy duty storage bag

Part No:MMKIT10
ERRP* $349.90

RECOVERY BAG - small

Bag included in 5PCE recovery kit
Also sold separately

Part No: MMKITBAG1
ERRP*: $59.00

RECOVERY BAG - large

Bag included in 8PCE recovery kit
Also sold separately

Part No: MMKITBAG2
ERRP*: $69.00

recovery damper

   

Back to top

Also known as a recovery blanket, they are one of the most important safety accessories you can own. Designed to eliminate the whipping action of a strap or winch cable in the event of a failure, they reduce the possibility of personal injury and vehicle damage. The damper comes in a high visibility safety orange with reflective tape for both day & night use. To install, simply fold the damper over the strap or cable and position midway between the vehicle and recovery strap.

Recovery Blanket

RECOVERY BLANKET

Quality orange vinyl winch cable damper with reflective silver stripes, hook and loop tape and a storage pocket on the inside. 90cm x 50cm, total weight of 1.1kg

Part No: MMRB
ERRP*: $49.00

equaliser straps

   

Back to top

The equaliser strap has been designed to evenly distribute the load on your vehicle during a recovery operation when connected to two rated recovery points. They are generally used in conjunction with a snatch strap or extension strap. Mean Mother equaliser straps are equipped with a moveable protective sleeve on the strap webbing.

equaliser-straps

EQUALISER STRAP

2.5m x 75mm 8000kg minimum breaking strength, grey polyester webbing. Movable protective sleeve in the middle and black reinforced eyelet protectors.

Part No: MMEQ8
ERRP*: $36.99
Minimum breaking strength 8,000kg

equaliser-straps

EQUALISER STRAP

2.5m x 75mm 12000kg minimum breaking strength, black polyester webbing with reflective text. 2 x Movable protective sleeves in the middle and black reinforced eyelet protectors.

Part No: MMEQ12
ERRP*: $54.90
Minimum breaking strength 12,000kg

tree trunk protectors

   

Back to top

Tree trunk protectors are designed to protect the tree used as an anchor point for your recovery. If you use anything other than a tree trunk protector you risk damaging both the tree and your winching line and over time may also cause the tree to die.

trunk protector

TREE TRUNK PROTECTOR

3m x 75mm, 6500kg minimum breaking strength. White polyester webbing, Black reinforced eyelets protectors.


Part No: MMTTP
ERRP*: $35.99
Minimum breaking strength 6,500kg

trunk protector

TREE TRUNK PROTECTOR

3m x 75mm, 12000kg minimum breaking strength. Black polyester webbing with reflective text, black reinforced eyelet protectors. Comes with 2 x MM neoprene sleeves.

Part No: MMTTP123
ERRP*: $54.90
Minimum breaking strength 12,000kg

trunk protector

TREE TRUNK PROTECTOR

5m x 75mm, 12000kg minimum breaking strength. Black polyester webbing with reflective text, black reinforced eyelet protectors. Comes with 2 x MM neoprene sleeves.

Part No: MMTTP125
ERRP*: $64.90
Minimum breaking strength 12,000kg

winch straps

   

Back to top

An extension strap is the ideal accessory to any winch, either hand or electric. They are used to extend the length of a winch cable should it not be long enough to anchor to a suitable recovery point once fully extended.

Winch Straps

10M X 50MM - 4.5T

4500kg minimum breaking strength. Black polyester webbing, yellow reinforced eyelets protectors.

Part No: MMW10
ERRP*: $44.99
Minimum breaking strength 4500kg

Winch Straps

10M X 60MM - 8T

8000kg minimum breaking strength. Blue polyester webbing with reflective text, black reinforced eyelet protectors. Comes with 2 x neoprene MM sleeves.

Part No: MMW810
ERRP*: $79.90
Minimum breaking strength 8000kg

Winch Straps

20M X 60MM - 8T

8000kg minimum breaking strength. Blue polyester webbing with reflective text, black reinforced eyelet protectors. Comes with 4 x neoprene MM sleeves.

Part No: MMW820
ERRP*: $129.90
Minimum breaking strength 8000kg

4wd jack

   

Back to top

One of the most practical recovery accessories you can have is a Mean Mother 4wd jack. It can be used in situations where it is necessary to lift, winch, clamp, pull and push. They are useful in lifting a vehicle clear from obstacles that come into contact with the underbody. By lifting the vehicle holes can be filled or articles such as rocks, wood or sand tracks can be positioned to assist in creating traction for the wheels.
The Mean Mother 4wd jack stands at a total height of 48” (122cm). It has a minimum lowered height of 11cm and a maximum lifting height of 102cm. With a Working Load Limit (WLL) of 1500kg, the jack also complies with the mandatory requirements of AS/NZS2693:2007.

48 inch jack sand base jack jack carry bag jack wheel mount

4wd JACK 48INch

Working Load Limit 1500kg, total height: 48” (122cm), height lowered: 110mm, height raised: 1020mm. Complies with the mandatory requirements of AS/NZS2693:2007.

Part No: MMHLJ
ERRP*: $149.00

4wd JACK SAND BASE

Suits MMHLJ.




Part No: MMHLJB
ERRP*: $64.90

4wd JACK CARRY BAG

Suits MMHLJ.




Part No: MMHLJBG
ERRP*: $19.95

4wd JACK WHEEL MOUNT

Suits MMHLJ. Made from quality aluminium.



Part No: MMHLJWM
ERRP*: $119.00

exhaust jack

   

Back to top

Air jacks are the perfect recovery item for any off road traveller exploring areas where soft sand, snow & mud might be encountered. When a vehicle gets bogged in these conditions a normal jack is useless as it will sink into the ground. The Mean Mother air jack can raise a vehicle high enough so you are able to position rocks, wood or other objects to assist in creating traction for the wheels. It works by using the vehicle’s exhaust gases from the tailpipe to inflate the air bag. Alternatively it can be inflated using an onboard or portable air compressor.
The air jack bag features a toughened double layer reinforced lifting surface which provides stability and control when raising a vehicle. Constructed from heavy duty high tenacity nylon, it’s coated with plasticised PVC to provide maximum strength and resistance against tearing. Special triangular feet built into the base provides superior grip and maximum grounding in all conditions. Exhaust jacks are not an alternative to the vehicle’s factory supplied jack, they are a serious recovery product.

CautionTIP:
The jack relies on pressure from the exhaust system for inflation, therefore the exhaust must not have any holes, spot-welded chrome extensions or gas leaks otherwise it will not be able to build up enough pressure to inflate the bag and lift the vehicle.
Winch Straps

EXHAUST JACK

4000kg maximum gross vehicle mass (GVM)
Kit includes: 1 x 5m exhaust hose
1 x 1m extension hose
1 x air compressor adaptor
1 x pair of leather gloves
1 x puncture repair kit (3 patches + 1 glue)
2 x protective mats
1 x yellow carrying zipper storage bag
1 x instruction manual
Two year warranty

Part No: MMEXJ
ERRP*: $249.00
Maximum GVM 4000kg

air jack kit

air jack kit 2

air jack bag

recovery gloves

   

Back to top

These Mean Mother leather recovery gloves have been made using premium grain leather and feature stitch free palms, a winged thumb and elastic cuff. Leather gloves are extremely important when handling recovery accessories, equipment or wire cable as they offer protection to your hands.

CautionInjuries to hands often occur during a recovery from wire cables which have splintered or burred, pinching skin between mechanisms of a high lift jack, cutting fingers while handling and securing shackles or recovery points. There are many ways you could cause injury to yourself while attempting a recovery however by wearing leather gloves you will reduce the likelihood of injury to your hands.
recovery gloves

OFFROAD RECOVERY GLOVES

These gloves are sold as a pair, large size. Made using quality leather.



Part No: MMLG
ERRP*: $15.99

pocket chain saw

   

Back to top

This is a versatile piece of equipment ideal for any camping or recovery kit, and perfectly suited to any outdoor enthusiast needing a compact, lightweight, wood cutting solution.

Perfect for clearing a path by removing low hanging branches, cutting up wood for a campfire, or clearing a wooden obstacle that is across a track - This is a must have inclusion for any travel kit.

Caution
When using the Pocket Chain Saw, ALWAYS use hand protection to eliminate the possibility of cuts caused by the blade of the saw.
pocket chain saw

pocket chain saw

Features a cutting blade at every drive link along the chain for faster and easier cutting.



Part No: MMPCS1
ERRP*: $39.95

deep dish tray mats

   

Back to top

Made using quality, durable and hard wearing PVC the high walls of these mats are designed to trap dirt, stones, grass and mud, protecting your vehicles interior. The front mats have guidelines which allow you to trim the mats for a neater fit. Simply hose to clean and unlike rubber mats, PVC mats do not create unpleasant odours.

front mats

TRAY MAT FRONT - BLACK

Sold singly,
71cm x 50cm PVC front tray mat.
Total weight 1.60kg.






Part No: MM4800
ERRP*: $16.90

TRAY MAT FRONT - grey

Sold singly,
71cm x 50cm PVC front tray mat.
Total weight 1.60kg.






Part No: MM4801
ERRP*: $16.90

rear mats

TRAY MAT REAR - black

Sold singly,
47cm x 50cm PVC rear tray mat.
Total weight 1.10kg.




Part No: MM4850
ERRP*: $11.90

TRAY MAT REAR - grey

Sold singly,
47cm x 50cm PVC rear tray mat.
Total weight 1.10kg.




Part No: MM4851
ERRP*: $11.90

MAXI 4X4 2 AIR COMPRESSOR 110L/MIN

Back to top

air compressor 1

 

Part No: MMACM2
ERRP*: $249.00

  • Massive 110L/min f.A.D
  • 45mm cylinder
  • 0.65hp (0.48Kw) permanent magnet motor
  • 2.4m power leads with quality battery clips
  • Rubber hoses
  • Screw or thumb lock valve adaptors
  • 55 minute duty cycle
  • Can be permanently mounted
general information
Specifications 110L/min
Voltage 12 volt
Cylinder 45mm
Maximum current 40amp
Maximum pressure
150psi
Thermal cut out protection
Yes - active at 105°C
Duty cycle
55 minutes at 40psi
Motor
0.65hp (0.48Kw)
Cooling Cooling fins
Power cables
2.4m with heavy duty battery clips
Control On/off toggle switch
Electrical current protection 40amp in line fuse
Adaptor hose 0.5m rubber hose with quick connectors, gauge and deflation button
Extension hose 5m rubber hose with quick connectors
Valve connectors 1 x screw type and 1 x thumb lock quick connector
Gauge 0-150psi
Overall dimensions
(L x W x H)
27cm x 14.5cm x 19cm
Net weight 5.6kgs
Base Metal sand tray with rubber feet. Can be permanently mounted to a vehicle
Storage Heavy duty bag with zipper
General Accessories 3 x accessory inflation adaptors for sporting / camping equipment
Operation Time V’s Pressure (tyre inflation)*
Tyre - 205/60 R16 Tyre - 275/70 R16
Time (minutes, seconds) PSI (kg/cm²) Time (minutes, seconds) PSI (kg/cm²)
0 min, 48 sec 14.2psi (1kg/cm²) 1 min, 42 sec 14.2psi (1kg/cm²)
1 min, 30 sec 28.4psi (2kg/cm²) 3 min, 24 sec 28.4psi (2kg/cm²)
2 min, 24 sec 42.6psi (3kg/cm²) 5 min, 24 sec 42.6psi (3kg/cm²)
3 min, 15 sec 56.8psi (4kg/cm²) 7 min, 30 sec 56.8psi (4kg/cm²)

Flow Rate (L/M) V’s Amp Draw V’s Pressure
(continues operation)*
Air Flow (L/min) Motor amp draw PSI (kg/cm²)
110L/min N/A 0psi (0kg/cm²)
105L/min 22amps 14.2psi (1kg/cm²)
80L/min 24amps 28.4psi (2kg/cm²)
68L/min 28amps 42.6psi (3kg/cm²)
60L/min 31amps 56.8psi (4kg/cm²)
55L/min 33amps 71psi (5kg/cm²)
*As tested at DC13V, individual results may vary depending on each compressor and environmental conditions.
compressor features

MAXI 4X4 3 AIR COMPRESSOR
110L/MIN

Back to top

air compressor 1

 

Part No: MMACM3
ERRP*: $269.00

  • Premium wireless remote
  • Massive 110L/min f.A.D
  • 45mm cylinder
  • 0.65hp (0.48Kw) permanent magnet motor
  • 2.4m power leads with quality battery clips
  • Rubber hoses
  • Screw or thumb lock valve adaptors
  • 55 minute duty cycle
  • Can be permanently mounted
general information
Maximum Air Flow 110 Litres per minute (29 Gallons per minute / 6,700 cubic inches per minute)
Voltage 12 Volt DC
Cylinder 45mm (1.8”)
Maximum current 40amp
Maximum pressure
150 PSI (1,034 kPa)
Thermal cut out protection
Active at 105°C (220°F)
Duty cycle
55 Minutes at 40 PSI (276 kPa)
Motor
0.65hp (0.48Kw)
Cooling Cooling fins
Power cables
2.4m (7.8’) with durable battery clamps
Control Premium wireless remote system & On/off toggle switch
Wireless remote control 2.4GHz <5.5dBm (3.6mW) - powered by 1 x 12V 23A L1028 battery (included)
Electrical current protection 40amp in line fuse
Adaptor hose 0.5m (1.65’) Rubber hose with quick connectors, gauge & air bleed-off button
Extension hose 5m (16.5") rubber hose with quick connectors
Valve connectors 1 x screw type and 1 x thumb lock quick connector
Gauge 0-150 PSI (0-10 BAR / 0-1,034 kPa)
Overall dimensions
(L x W x H)
27cm x 14.5cm x 19cm (10.6” x 5.7” x 7.5”)
Net weight 5.6kgs (12.3lb)
Base Metal sand tray with rubber feet. Can be permanently mounted to a vehicle
Storage Heavy duty bag with zipper
General Accessories Inflation adaptors for camping & equipment
Operation Time V’s Pressure (tyre inflation)*
Tyre - 205/60 R16 Tyre - 275/70 R16
Time (minutes, seconds) PSI (kg/cm²) Time (minutes, seconds) PSI (kg/cm²)
0 min, 48 sec 14.2psi (1kg/cm²) 1 min, 42 sec 14.2psi (1kg/cm²)
1 min, 30 sec 28.4psi (2kg/cm²) 3 min, 24 sec 28.4psi (2kg/cm²)
2 min, 24 sec 42.6psi (3kg/cm²) 5 min, 24 sec 42.6psi (3kg/cm²)
3 min, 15 sec 56.8psi (4kg/cm²) 7 min, 30 sec 56.8psi (4kg/cm²)

Flow Rate (L/M) V’s Amp Draw V’s Pressure
(continues operation)*
Air Flow (L/min) Motor amp draw PSI (kg/cm²)
110L/min N/A 0psi (0kg/cm²)
105L/min 22amps 14.2psi (1kg/cm²)
80L/min 24amps 28.4psi (2kg/cm²)
68L/min 28amps 42.6psi (3kg/cm²)
60L/min 31amps 56.8psi (4kg/cm²)
55L/min 33amps 71psi (5kg/cm²)
*As tested at DC13V, individual results may vary depending on each compressor and environmental conditions.
compressor features

ADVENTURER 3 AIR COMPRESSOR 160L/MIN

Back to top

air compressor 1

 

Part No: MMACA3
ERRP*: $315.00

  • Premium wireless remote
  • Powerful 160L/Min F.A.D
  • 60mm cylinder
  • 0.73hp (0.54Kw) permanent magnet motor
  • 2.4m power leads with quality battery clips
  • Rubber hoses
  • Screw or thumb lock valve adaptors
  • 45 minute duty cycle
  • Can be permanently mounted
General information
Specifications 160 Litres per minute (42 Gallons per minute / 9,800 cubic inches per minute)
Voltage 12 volt DC
Cylinder 60mm (2.4”)
Maximum current 45amp
Maximum pressure
150 PSI (1,034 kPa)
Thermal cut out protection
Active at 105°C (220°F)
Duty cycle
45 Minutes at 40 PSI (276 kPa)
Motor
0.73hp (0.54Kw)
Cooling Cooling fins
Power cables
2.4m (7.8’) with durable battery clamps
Control Premium wireless remote & On/off toggle switch
Wireless remote control 2.4GHz <5.5dBm (3.6mW) - Powered by 1 x 12V 23A L1028 battery (included)
Electrical current protection Circuit breaker with reset button
Adaptor hose 0.5m (1.65’) Rubber hose with quick connectors, gauge & air bleed-off button
Extension hose 5m (16.5’) Rubber air hose with quick connectors
Valve connectors 1 x screw type and 1 x thumb lock quick connector
Gauge 0-150 PSI (0-10 BAR / 0-1,034 kPa)
Overall dimensions
(L x W x H)
32.5cm x 15cm x 26.5cm (12.8” x 5.9” x 10.4”)
Net weight 8.7kg (19.2lb)
Base Metal sand tray with rubber feet. can be permanently mounted to a vehicle
Storage Heavy duty bag with zipper
General Accessories Inflation adaptors for camping & equipment
Operation Time V’s Pressure (tyre inflation)*
Tyre - 205/60 R16 Tyre - 275/70 R16
Time (minutes, seconds) PSI (kg/cm²) Time (minutes, seconds) PSI (kg/cm²)
0 min, 36 sec 14.2psi (1kg/cm²) 1 min, 18 Sec 14.2psi (1kg/cm²)
1 min, 12 sec 28.4psi (2kg/cm²) 2 min, 36 Sec 28.4psi (2kg/cm²)
1 min, 48 sec 42.6psi (3kg/cm²) 4 min, 00 Sec 42.6psi (3kg/cm²)
2 min, 30 sec 56.8psi (4kg/cm²) 5 min, 30 Sec 56.8psi (4kg/cm²)

Flow Rate (L/M) V’s Amp Draw V’s Pressure
(continues operation)*
Air Flow (L/min) Motor amp draw PSI (kg/cm²)
160L/min N/A 0psi (0kg/cm²)
124L/min 38amps 14.2psi (1kg/cm²)
108L/min 40amps 28.4psi (2kg/cm²)
94L/min 42amps 42.6psi (3kg/cm²)
88L/min 43amps 56.8psi (4kg/cm²)
80L/min 43amps 71psi (5kg/cm²)
*As tested at DC13V, individual results may vary depending on each compressor and environmental conditions.
compressor features

tyre repair

   

Back to top

The Mean Mother tyre repair kit has all the necessary components to complete an emergency repair to a tubeless tyre. The kit features a set of long nose pliers which are handy for removing objects imbedded in the tread.

recovery gloves

TYRE REPAIR KIT HEAVY DUTY

Kit includes:
1 x long nose pliers
1 x reamer tool
1 x insert tool
2 x allen keys
1 x lubricant
20 x repair cords
1 x knife
1 x storage case.

Part No: MMTG200
ERRP*: $44.99

tyre gauges

   

Back to top

Mean Mother tyre gauges are shock resistant, reliable, easy to read and operate. They have ANSI (American National Standards Institute) grade B accuracy. All our gauges have been tested to ANSI standards for their precision and accuracy. The classifications relate to the scale of the gauge. The scale of the gauge, commonly referred to as the pressure range is divided into three equal portions when characterising its accuracy. For example 0-20psi, 20-40psi and 40-60psi portions of the dial. Mean Mother gauges have a Grade B accuracy, meaning the accuracy for the 0-20psi and 40-60psi portions fall to within 3% of the actual pressure being measured.

The middle portion is the most accurate and in this case would be accurate to within 2% of the pressure being measured. When selecting a gauge for your application you should select one where the middle portion will be the pressure range required. For this reason all Mean Mother gauges are 0-60psi which is most suited to the 4WD and standard vehicle market.

Mean Mother tyre gauges achieve this accuracy and reliability because of the quality of components and design. They feature a unique diaphragm made from a composite material that is sensitive to even the slightest change in pressure and will never lose their shape. Most common tyre gauges are constructed using a bourdon tube with mechanical gears. Its generally acknowledged that when the bourdon tube receives a sudden boost of pressure the internal gearing activates to move the pointer. The gears can easily fail as a result of the torque generated from this action.

48 inch jack 48 inch jack sand base jack jack carry bag

tyre deflator and gauge


2” Dial, 0 - 60 psi, braided flexible air hose. ANSI grade B accuracy. Quick release deflator and gauge attachments. Pressure release button on stem. Shock resistant. Quality zipper storage pouch.


Part No: MMDK01
ERRP*: $69.90



 


PRESSURE GAUGE 60lb


2” Dial, 0 - 60 psi, ANSI grade B accuracy. Straight tyre valve connector and air release button. Handy storage case.


Part No: MMTG60
ERRP*: $22.90

 

 

 


PRESSURE GAUGE 2INCH W/
EXT HOSE

2” Dial, 0 - 60 psi, braided extension hose. ANSI grade B accuracy. 45° angled valve connector with deflation nipple and air release button. Quality zipper storage pouch.


Part No: MMTGE2
ERRP*: $55.90




PRESSURE GAUGE 3 1/2 INCH

3 1/2” Dial, 0 - 60 psi, 45cm rubber (NBR) extension hose. Rubber body impact protection cover. ANSI grade B accuracy. 360° swivelling brass valve connector with deflation nipple and air release button. Stored in a blow mould case.

Part No: MMTG312
ERRP*: $79.90


hand winches

Back to top

Hand winches are a must have accessory if you don’t have an electric winch. The main advantage of a hand winch is it does not rely on the vehicle’s power system and can be used and transferred between vehicles. The 1600kg winch is the most common as its weight is only 12kg making it easy to carry and setup for a recovery. The 3200kg winch has obvious benefits in its capacity however it is a much heavier unit at 23kg which can make a recovery setup more difficult.

Working on a simple principle a set of jaws inside the unit, clamp the wire cable and pull it through the unit. A great feature of the hand winch is that it can operate in both forward and reverse. Shear pins are installed in the winching handle as a safety precaution just in case the load is in excess of the rated winch capacity. It is a good idea to always travel with spare shear pins and each Mean Mother hand winch comes with spare pins located in the handle.

Hand winches are simple to use and maintain although the process of recovering a vehicle can be slow and physically straining on the operator. Stopping during a recovery is not recommended as the unnecessary forces left on the winch and winching lines may cause damage or failure to the product. We recommend the use of a snatch block to reduce strain in these instances. Only use genuine wire cables and do not replace the cable with one that has a different specification to the original.

Hand Winch Specifications hw1600 hw3200
Rated forward hand power (N) 438 438
Rated capacity (kg) 1600 3200
Rated forward travel (forward & backward) (mm) ≥55 ≥28
Wire cable dimensions 20m x dia (mm) 11 16
Maximum traveling load (kg) 2400 4000
Net weight (kg) 12 23
Unit dimensions (mm) 545 x 284 x 97 660 x 325 x 116
Black Tow Hooks

1600KG RATED CAPACITY
WITH 11mm x 20M CABLE

Part No: HW1600
ERRP*: $379.00

Hand Winch 3200kg

3200KG RATED CAPACITY
WITH 16mm x 20M CABLE

Part No: HW3200
ERRP*: $549.00

Black Tow Hooks

REPLACEMENT WIRE CABLE TO SUIT HAND WINCH - 11MM X 20M

Part No: HW1600C
ERRP*: $199.00

Black Tow Hooks

REPLACEMENT WIRE CABLE TO SUIT HAND WINCH - 16MM X 20M

Part No: HW3200C
ERRP*: $299.00

Recovery Hitch

   

Back to top

Made from high strength steel this hitch is the only safe way to attach a recovery device to a vehicles towing system. Hitch comes complete with a 4.7T coated bow shackle. This unit is suitable for most general winch or strap recoveries.

Winch Straps

Hitch Receiver

Includes high visibility bow shackle.
Overall length 175mm.
Complies to AS/NZS 2741.2002

Part No: MMRHS
ERRP*: $49.99

foldable shovel

   

Back to top

Often overlooked, the humble folding shovel is an essential piece of equipment. It comes with a handy storage bag for the shovel and any dirt from the recovery, to keep your vehicle clean.

foldable shovel

FOLDABLE SHOVEL

Folds in three sections, comes with a storage bag. 580mm total extended length, 240mm folded length

Part No: MMFS
ERRP*: $24.95

MULTI SHOVEL

Back to top

This unique design offers you everything from a small spade to full sized long handle shovel to easily shift sand and dirt at a rapid rate. Its versatility is unmatched with up to five different configurations to suit most recovery situations. With a PE outer skin and reinforced steel core, it’s strong enough to handle the toughest of conditions and comes packed neatly in its own custom storage bag.

 

MULTI SHOVEL

Part No: MMSHV
ERRP*: $129.00